Flat Head w/Nibs Particle Board Screws, Type ‘17’, Black Oxide- Lengths:1" - 3"
- Asymmetrical thread pattern
- Type ’17’ reduces wood splitting
- Counter sinking nibs for a flush finish
- Resists material slippage during pull out and vibration
- Superior holding power
| Installation Attaches wood or metal to concrete, brick, cement block or masonry.  A standard screw gun with torque limiting nose piece set at a maximum of 3000 RPM drive speed recommended. Use a #2 reducedPhillips drive bit. The fastener is completely installed when the fastener head is seated flush with the work surface. Do not over torqueas it can cause the head to snap or damage to the work surface. |
Flat Head w/Nibs Particle Board Screws, Type '17', Zinc Plated- Lengths: 3/4" - 3"
- Asymmetrical thread pattern
- Type ’17’ reduces wood splitting
- Counter sinking nibs for a flush finish
- Resists material slippage during pull out and vibration
- Superior holding power
| Installation Attaches wood or metal to concrete, brick, cement block or masonry.  A standard screw gun with torque limiting nose piece set at a maximum of 3000 RPM drive speed recommended. Use a #2 reducedPhillips drive bit. The fastener is completely installed when the fastener head is seated flush with the work surface. Do not over torqueas it can cause the head to snap or damage to the work surface. |
Flat Head Particle Board Screws- Lengths: 3/4" - 3"
- Asymmetrical thread pattern
- Square drive prevents cam out and stripping
- Resists material slippage during pull out and vibration
- Superior holding power
| Installation Attaches wood or metal to concrete, brick, cement block or masonry.  A standard screw gun with torque limiting nose piece set. The fastener is completely installed when the fastener head is seated flush with the work surface. Do not over torqueas it can cause the head to snap or damage to the work surface. |
Flat Head Particle Board Screws, Hinge Screw- Lengths: 1/2" - 3/4"
- Asymmetrical thread pattern
- Flat head for counter-sinking
| Installation Attaches wood or metal to concrete, brick, cement block or masonry.  A standard screw gun with torque limiting nose piece set.The fastener is completely installed when the fastener head is seated flush with the work surface. Do not over torqueas it can cause the head to snap or damage to the work surface. |
Oval Head Particle Board Screws, Hinge Screw- Lengths: 5/8"
- Asymmetrical thread pattern
- Used to attach hinges to cabinets and drawers
| Installation Attaches wood or metal to concrete, brick, cement block or masonry.  A standard screw gun with torque limiting nose piece set.The fastener is completely installed when the fastener head is seated flush with the work surface. Do not over torqueas it can cause the head to snap or damage to the work surface. |
Pan Head Face Framing, Type ‘17’- Lengths: 1-1/4" - 1-1/2"
- Fine thread for hardwoods
- Type ’17’ reduces wood splitting
- Superior holding power
| Installation Attaches wood or metal to concrete, brick, cement block or masonry.  A standard screw gun with torque limiting nose piece set. The fastener is completely installed when the fastener head is seated flush with the work surface. Do not over torqueas it can cause the head to snap or damage to the work surface. |
Pan Head Face Framing, Coarse Thread, Type ‘17’- Lengths:
- Coarse thread for soft woods
- Type ’17’ reduces wood splitting
- Square drive prevents cam out and stripping
- Superior holding power
| Installation Attaches wood or metal to concrete, brick, cement block or masonry.  A standard screw gun with torque limiting nose piece set.The fastener is completely installed when the fastener head is seated flush with the work surface. Do not over torqueas it can cause the head to snap or damage to the work surface. |
Draw Bolt, Joint Fastener- Lengths: 1/4-20 x 3-1/2"
- For counter-top assembly
- Adjust without special tools
| Installation Attaches wood or metal to concrete, brick, cement block or masonry.  A standard screw gun with torque limiting nose piece setThe fastener is completely installed when the fastener head is seated flush with the work surface. Do not over torqueas it can cause the head to snap or damage to the work surface. |
